Skip to main content


The ES i-Vu® Pro Advanced course is the fifth in the Controls Expert Training Series. This course will provide a technician the necessary skills to install, commission and support Carrier’s i-Vu® Open Pro user interface solution.

duration cost format register*
1 day $175 classroom 11/6/2019†

*To obtain a registration link for this class, please contact your local Carrier Sales Office Controls Representative.

†Class registration closes on 10/7/2019.

Automated Logic Corporation has been accredited as an Authorized Provider by the International Association for Continuing Education and Training (IACET), 12100 Sunset Hills Rd., Suite 130, Reston, VA 20190; (703) 234-4065. BAS University is the continuing education organization of Automated Logic Corporation.


Class Overview

The ES i-Vu Pro Advanced course is the fifth in the Controls Expert Training Series. This course will provide a technician the necessary skills to install, commission and support Carrier’s i-Vu® Open Pro user interface solution. This course is exclusive to registered Carrier Controls Expert Offices. For more information on the Carrier Controls Expert Program, please contact your local Carrier Controls sales representative or visit

Who Should Attend this training

This course is intended for new and existing Carrier Controls Expert ES level technicians to ensure they can properly use and setup an i-Vu® Pro system in the field. This course is a required component for both new and existing ES level technicians.

HVAC Training Objectives

Learning Objectives

At the conclusion of this course, each student should be able to:

  • Start-up a typical i-Vu® Pro system
  • Perform advanced system and network troubleshooting
  • Utilize the following i-Vu® Pro tools/applications
    • SNAP
    • ViewBuilder 
    • SiteBuilder 
    • EquipmentBuilder

Learning Methods Used

This course uses a combination of classroom lecture, demonstrations using the controls simulators, computer lab and workshops to present the material. Student’s achievement of the learning objectives is determined by successful completion of the workshops, and final written exam. Workshops are instructor guided exercises using the procedures taught in the lectures.


Topics Covered

All times are approximate and shown as (classroom hours/lab or workshop hours).

  • Create, commission and modify an i-Vu® Pro system (0.5/0.5)
  • Create a system on an i-Vu® Pro server (0.5/0.5)
  • Verify IP network cable connections (0.5/0.5)
  • Verify server’s IP address (0.5/0.5)
  • Verify or set Open Router IP address (0.5/0.5)
  • Verify IP network communication (0.5/0.5)
  • Capture BACnet IP traffic (0.5/0.5)
  • Verify or set MAC addresses (0.5/0.5)
  • Verify BACnet MS/TP network communication (0.5/0.5)
  • Upload/Download memory through the network (0.5/0.5)
  • Capture and analyze BACnet MS/TP traffic (0.5/0.5)
  • Read logic (0.5/0.5)
  • Edit logic (0.5/0.5)
  • Discover a sequence of operation (0.5/0.5)
  • Assign physical inputs and outputs to microblocks (0.5/0.5)
  • Map to a point in another control program (0.5/0.5)
  • Check system for errors (0.5/0.5)
  • Fix a graphics page error (0.5/0.5)
  • Verify values on a graphics page (0.5/0.5)
  • Create a reusable graphic (0.5/0.5)
  • Back up your system files (0.5/0.5)
  • Combine database clippings into one system (0.5/0.5)
  • Download files from a remote server (0.5/0.5)
  • Modify a control program and graphic (0.5/0.5)
  • Upload files to a remote server (0.5/0.5)
  • Fix an i-Vu® Pro system (0.5/0.5)
  • Install, troubleshoot, and commission a sabotaged i-Vu® Pro system (0.5/0.5)

Class Requirements

Completion Requirements

To receive a certificate for this course student must be present for the entire course, complete all workshops and receive a grade of 70% on graded final.

Prerequisite requirements

IS Certified - minimum of 12 months


An introductory knowledge of commercial air conditioning and heating systems, commercial building design and design process is desirable. A working knowledge of controls and control theory is also required. Familiar with i-Vu® and building automation systems.


You will need to bring with you a laptop and mouse with these requirements:

  • 2 GHz processor
  • 1 GB RAM
  • 2 GB Disk Space
  • 1 USB Port
  • Internet Explorer 8, 9 or 10
  • DVD Drive
  • Windows 8 Enterprise or Professional (32 or 64 bit) OR Windows 7 Pro or Ultimate (32 or 64 bit) OR Windows Vista Business or Ultimate Editions (32 or 64 bit)
  • i-Vu®Tech Tools (part number: USB-TKIT) version 6.0 with latest patches.
  • USB-L Kit


Students in this course receive a course workbook.


This class is held in a class and business casual dress is appropriate. Any safety equipment required for these lab tours will be furnished.


Class starts at 8 AM Monday and runs from 8 AM till 5 PM each day including Friday if class is scheduled at the end of a week. Travel arrangements should be made accordingly.


All courses are taught at BAS University (Kennesaw, GA), unless noted otherwise. Location and lodging information will be provided at the time of registration.